Best welding guides: how to become a more skilled welder and how to pick the top welding equipment. The arc is shaped like a cone, with the tip at the electrode and the base on the metal being welded. The closer the electrode is held to the metal, the smaller the base of the cone — but as you pull the electrode farther away, the base (and puddle) gets larger. If the puddle gets too large, gravity will simply pull it away from the base metal, leaving a hole. This is why thin-gauge metals are especially challenging for beginners. Perhaps the most important skill needed for TIG welding is moving the torch in a controlled manner, with steady forward movement, while keeping the gap between the tip of the electrode and the base metal consistently small — usually in the range of 1/8 inch to 3/16 inch. It requires a lot of practice to precisely control the arc length, keeping it as short as you can without allowing the electrode to touch the base metal or filler rod.
In many shops, the operator has to go to a tool room or supply area for a new contact tip, coil of wire or other welding accessory. This takes valuable time away from the welding cell and slows down overall productivity. To improve the operating efficiency and minimize wasted time, companies should stock at least a limited supply of all necessary items near the welding station – this includes shielding gas, flux and wire. Another helpful productivity enhancing tip is to switch to larger spools of wire such as from 25 lb. spools to 44 or 60 lb. spools to even larger packages of 1,000 lb. reels or 1,000 lb. drums. A simple switch like this means less changeover time, which adds up over the weeks, months and years. Shops should also be on the lookout for shielding gas waste. A simple device called a surge turbine can be placed at the end of the gun to provide a digital readout of the gas surge and flow rate. If the surge rate is high, investing in a surge guard can reduce the pressure, eliminating gas surges and waste. Leaks in the gas delivery system can also create a potential loss of money. By looking at the amount of consumables purchased each year and then examining the total gas purchased, a company can determine if there is a significant loss. Welding manufacturers and distributors should be able to provide average utilization figures so that loss can be detected. If there is a loss suspected, one of the easiest ways to check for leaks is to shut off the gas delivery system over the weekend. Check the level on Friday evening and then again on Monday morning to determine if gas was used while the system was in shut down mode.
Several advices on welding equipment, MIG and TIG welders, plasma cutters. When appearance counts, TIG welding creates a high quality, clean weld that is far less likely to distort the metal by using a nonconsumable tungsten electrode. There is no need to worry about splatter because it only uses the necessary amount of filler metal needed in the welding puddle, making for the highest quality weld in every respect. However, TIG is fairly specialized and requires a good deal of training in order to master it-so make sure any TIG welder purchase is paired with a plan to take welding classes. Instead of the point and shoot simplicity of MIG welding, TIG requires the use of a foot pedal to regulate the welding process. A filler rod that is separate from the torch that must be fed in gradually. Many professional welders prefer TIG because it can weld a wide variety of metals and because of the versatility of argon gas used during TIG welding. There is no slag to block the view of the weld puddle. Argon gas can weld any metal at any thickness with TIG welding, and therefore there is no need to change the gas depending on the project.
Welding faster may sound appealing, but aside from practice, there are few shortcuts when creating a strong weld. In fact, unless a situation calls for a fast-moving weld, there’s a good chance that slow and steady is the way to go. An online search for ways to weld faster, will yield either descriptions of the ways automated welding has increased welding speed or press releases from companies who claim their gas or electrode holds the key to improving welding speed. In other words, it can seem like spending a lot of money is the only way to weld faster. However, for those looking for some ways to save time on their welding projects, there are some ways to weld faster for certain projects. While it’s not always a good idea to find a way to weld faster, there are situations when welding faster may produce a better product or a few simple changes can speed up the time on task. Read additional details at MIG Welding Machines.
And another tip is use the old school type of collet body(not gas lens) and one size smaller cup than you would use for steel that still provides good shielding. A smaller old school (not gas lens) TIG cup confines the shielding gas envelope to the puddle so that arc energy is not wasted in the form of frosty cleaning action outside the weld. A lot of Old timers use the small cups, they just don’t know why. Pay attention next time you weld aluminum and use a small cup and then turn the shielding gas flow down to around 12-15 cfh with a #6 cup and see if things don’t quiet down a bit.